Falcon Metal Logo
 
Falcon Metals Group
Distributors
 
HOME
ABOUT
PRODUCTS
REFERENCE INFO
CONTACT
SEARCH CATALOG
OUR CATALOG
 
 

Metal Physical Properties

STAINLESS STEEL COIL, FOIL & STRIP

Specialty: Thin and Tempered Coil

200 * 300 * 400 * PH GRADES <> TEMPERED & ANNEALED <> COIL: .001 to .250
SLITTING - EDGING - POLISHING - CUT TO LENGTH

FULL SIZE AND CUT - TO - SIZE SHEET & PLATE

TEMPERED AND ANNEALED SHEET ----- <> PLATE TO 8" THICK

   *PROCESSED FLAT BAR:    .125 x .500 TO 1" x 18"

*Processed Flat Bar is Plate Sheared, Straightened & Edged...

"A significant cost savings vs true flat bar"
Shearing, Plasma or Water Jet Plate Cutting ... Machining available on cut-outs.

 

 

SS GRADE

201

202

301

302

304

304L

305

316

316L

321

347

405

409

430

410 6

420 6

PH17-7

  PHYSICAL PROPERTIES 

Density(lbs.per cu.in)

.287

.287

.290

.287

.287

.287

290

.286

.286

.285

.290

.280

.280

.278

.278

.278

.282

Modulus of Elast.
(X10 6 PSI)

26.6

28.6

28

28

28

28

28

28

28

28

28

29

29

29

29

29

29.5

Electrical
Resistivity 1

423

427

432

432

432

432

432

444

444

432

438

360

360

360

342

330

480

Thermal
Conductivity 2

9.4

9.4

9.4

9.4

9.4

9.4

9.4

9.3

9.3

9.3

9.2

-

-

13.1

14.4

14.4

9.5

Coefficient of
Thermal Expansion 3

8.9

9.7

9.4

9.6

9.6

9.6

9.6

8.9

8.9

9.3

9.3

6.0

6.0

5.8

5.5

5.7

8.5

Cost Factor 4

.87

.95

.95

1.00

1.00

1.13

1.39

1.56

1.68

1.35

1.62

.88

-

.73

.76

-

2.18
TENSILE STRENGTH (x 1000 PSI)

ANNEALED

115-135

95 Min.

125-145

95-110

90-100

100 Max.

85-110

90-110

65 Nom.

NA

70-80

80-95

95 Nom.

150 Max.

1/8 HARD





100-120

100-120





95-110




1/4 HARD

125-150


125-150

125-150

120-135

125-150





125 Min.



153 Nom.

1/2 HARD

150-175


150-175

150-175

135-150

150-175








180 Nom.

3/4 HARD

175-195


175-200

175-195










200 Nom.

FULL HARD

185 Min.


185 Min.

185-225

155-170

175-190





135 Min.



220 Nom.

SPRING

200 Min.


200 Min.












SPL SPRING 5



280 Min.7









180 Nom.

230 Nom.

240 Nom.

  YIELD STRENGTH (x 1000 PSI @0.2%Offset)

ANNEALED

45-60

40 Min.

40-60

38-50

35-45

40-55

30-45

40-55

40 Nom.


45-60

40-60

50 Nom.

65 Max

1/8 HARD





80-100

80-100





90-105




1/4 HARD

95-125


80-100

100-130

100-120

100-130





120 Nom.



94 Nom.

1/2 HARD

115-150


100-125

130-150

115-130

140-160








115 Nom.

3/4 HARD

140-165


145-160

150-170










148 Nom.

FULL HARD

160-185


160-200

170-210

135-160

160-180





130 Nom.



190 Nom.

SPRING

185 Min.


185 Min












SPL SPRING 5



250 Min 7









140 Nom.

195 Nom.

225 Nom.

ELONGATION (% in 2 inches)

ANNEALED

45 Min.

40 Min.

45-75

40-65

50-66

40-65

40-71

46-58

25 Nom.


20-32

22-31

25 Nom.

25 Min.

1/8 HARD





20-40

30-40





3-8




1/4 HARD

25 Min.


35-60

30 Min.

15-25

12-25





1 Nom.



22 Nom.

1/2 HARD

15 Min.


25-50

7-15

7-15

4-10








10 Nom.

3/4 HARD

7 Min.


15-30

4-10










8 Nom.

FULL HARD

2 Min.


10-25

1-4

2-6

1-5





1 Nom.



5 Nom.

SPRING

1 Min.


1 Min.












SPL SPRING 5



1 Nom.7









15 Nom.

8 Nom.

6 Nom.

1. OHMS/CIR. MIL FT 2.BTU PER SQ. FT. PER HR. PER F @68F 3. INCHES PER INCH x 10 to the -6 FROM 32F- 212F 4. DISREGARD 5. TYPICAL HEAT TREATED PROPERTIES OF MARTENSITIC & PH STAINLESS STEELS 6. GENERALLY SOLD IN ANNEALED COND. 7. SPECIAL ROLLED SPRING TEMPER  

Above figures are theoretical

 
 
 
 
web design:
Bower Web Solutions
[ HOME ] [ ABOUT ] [ PRODUCTS ] [ REFERENCE INFO ] [ CONTACT ] [ OUR CATALOG ]

©2007-2010 Falcon Metals Group
All Rights Reserved